Weider WESY19510 Manual de usuario

USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find there are m

1015. Route the Long Cable (23) around the “V”-Pulley(6) on the Right Arm (48). Be sure that theCable is in the groove of the “V”-Pulley andthat the L

1119. Locate the Short Cable (58). Lay the ShortCable in the bracket on the Base (4). Attach the 3 1/2” Pulley (15) to the bracket with a 3/8” x 2”Bol

1222. Route the Short Cable (58) around the 3 1/2”Pulley (15) attached to the upper hole in the FrontUpright (42). See the inset drawing. Be surethat

24. Attach the Long Cable (23) to the Small “U”-Bracket (67) with a 1/4” Nylon Locknut (2) and a1/4” Flat Washer (10). See the inset drawing.Do not ov

1426. Press a 1 1/2” Square Inner Cap (32) into theSeat Frame (36).Insert the 1/4” x 2” Carriage Bolt (38) into thecenter hole in the Seat Plate (37).

1529. Press a 3/4” Round Inner Cap (34) into each endof both 12 1/2” Pad Tubes (28). Insert one 12 1/2” Pad Tube (28) into the SeatFrame (36). Slide a

16ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t

17ATTACHING THE LEG LEVER TO THE LOWPULLEY STATIONTo use the Leg Lever (29), the seat must be attachedto the front upright (see ATTACHING AND REMOV-IN

18WEIGHT PRESS ARM BUTTERFLY ARM LEG LEVER HIGH PULLEY LOW PULLEYPLATES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)Top 20 10 15 14 2 4145 22 36 28 54270 33 54

19TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. Theweight sy

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20CABLE DIAGRAMThe cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use thediagram to be sure that the tw

21NOTES

22Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY19510 R1101A1 2 5/16” x 2 1

231111885527121544157123272144213616035615122575821355114192651256463769213341276515714110433216507427506216970697047484445444513403837183228303410224

ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6

This chart is provided to help you identify the small parts used in assembly. Important: Some parts mayhave been pre-assembled for shipping purposes;

5/16" Nylon Locknut (3)1/4" Flat Washer (10)5/16" Flat Washer (8)3/8" Flat Washer (9)1/4" x 2 1/2" Screw (43)5/16"

1" Retainer (69)3/8" x 2" Bolt (12)3/8" x 3 1/2" Bolt (16)3/8" x 2 1/2" Bolt (7)3/8" x 3 3/4" Bolt (71)3

1" Round Inner Cap (49)1" Round Cover Cap (70)1/2" x 3/4" Spacer (61)Round Inner Cap (77)1 1/2" Square Inner Cap (32)1 3/4&qu

3WARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the weight system.IMPORTANT PRECAUTIONSWARNING: B

4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76 in.Width: 37 in. Length: 48 in. Foot PlateLow Pulley StationHigh Pulley StationLeft SideRight SideLa

5156High Side of Bracket3551511412741. Before beginning assembly, be sure that youhave read and understand the information inthe box above.Press a 2”

62. Slide the Front Upright (42) onto the 5/16” x2 1/2” Carriage Bolts (1) in the Base (4). Handtighten a 5/16” Nylon Locknut (3) onto eachCarriage Bo

75. Press the Weight Tube Bumper (64) into the endof the Weight Tube (63). Insert the Weight Tubeinto the stack of Weights (25). Be sure that thepins

88. Press a 1 3/4” Square Inner Cap (44) into the topof a Press Arm (46). Press a 1” Round Inner Cap(49) into each end of the handle on the PressArm.

911. During steps 11 through 24, refer to the CABLEDIAGRAM on page 20 of this manual to verifyproper cable routing. Before beginning this sec-tion, id